1 / 4

Vit dagføra vøruupplýsingarnar. Vit fara ígjøgnum allar vørulýsingarnar í vørusavninum. Upplýsingarnar um nýtsluøki og tilfar, sum vøran kann brúkast til, kunnu vera skeivar, meðan vit skráseta rætta tilfarið fyri hvørja vøru. Ert tú í iva, spyr tín kontaktpersón hjá A4.

Application area

The EPDM outer film is 1.2 mm thick and is used to seal the exterior bottom connections of doors and floor-level windows in outer walls and conservatories. It is also used to seal connections in roofs and balconies. The 0.75 mm thick version of the exterior EPDM film is ideal for the external sealing of construction elements in the façade area and for sealing underneath window sills.

Vørulýsing

The EPDM film is an elasticated elastomer membrane made of EPDM rubber. It is used for external sealing.

Fyrimunir

Water-repellent yet permeable to water vapour
Very good elasticity
Outstanding resistance to UV and weathering
Extreme temperature resistance
Shelf life "unlimited" at +5 °C to +25 °C

Góð ráð

Application:
The adhesive surfaces must be load-bearing and stable. The surfaces must be free from dust, release agents, oil, grease, moisture and ice.
Cut the EPDM film to the desired length. Glue the surfaces of the film and/or the base material to be bonded using EPDM film adhesive (art. no.: 0898 800 010) by applying the film adhesive to the base material in a bead of approx. 5 mm without interruption.
Then press the EPDM film into the adhesive layer without applying any pressure and loosen it again if necessary so that the solvents can flash off from the adhesive on larger surfaces. Then glue the film to the designated base material and carefully press it using a press-on roller (art. no.: 0693 603 002).
The adhesive properties of EPDM films may vary so it is always advisable to perform tests beforehand. Film overlaps must be at least 50 mm in width. If necessary, carry out further bonding to prevent the film from slipping.
The EPDM film must always be installed without tension. The film is also mounted on the window with a clamping batten, socket rail or other fastening, as described in DIN 18195 (DIN 18531, requirement in accordance with DIN SPEC 20000-201 and DIN 18533, requirement in accordance with DIN SPEC 20000-202).
EPDM films are not suitable for sealing against pressurised water and cannot be plastered or painted over. The film is generally compatible with bitumen substrates that are commonly used in construction.

Design

Without self-adhesive strips

Composition of set

1 roll of 25 m = 25 m

Faklig nærlýsing

Adhesive base	Acrylate
Building material class	B2 - Normally inflammable
Building material class conditions	in accordance with DIN 4102
Building material class/conditions	B2 - Normally inflammable / in accordance with DIN 4102
Building material compatibility	Conventional building materials
Chemical basis	Ethylene propylene diene natural rubber
Colour	Black
Composition of set	1 roll of 25 m = 25 m
Design	Without self-adhesive strips
Length of roll	25 m
Max. processing temperature	+35 °C

Max. temperature resistance	+130 °C
Min. processing temperature	+5 °C
Min. temperature resistance	-40 °C
Min./max. processing temperature	+5 to +35 °C
Min./max. temperature resistance	-40 to +130 °C
Stretch capacity	300 %
Thickness	0.75 mm
Ultraviolet resistance	Yes
Water-vapour diffusion resistance factor value µ	32000
Width	100 mm
Width x thickness	100 x 0.75 mm

Væntað veiting: 29.–30. sep.

Bílegg í seinasta lagi mikudagin kl. 23:59 · bíleggingin verður send til Reca hósdagin

Exterior EPDM film, thickness 0.75 mm, 1 roll of 25 m, 100 mm x 25 m

The EPDM film is an elasticated elastomer membrane made of EPDM rubber. It is used for external sealing.

Vørunummar	0800601100
EAN	4029484439584
Pakkieind	1 stk
Adhesive base	Acrylate
Building material class	B2 - Normally inflammable
Building material class conditions	in accordance with DIN 4102
Building material class/conditions	B2 - Normally inflammable / in accordance with DIN 4102
Building material compatibility	Conventional building materials
Veitari	RECA NORM